 |
|
|
|
 |
|
Hayward Pro Series Sand Filter Systems for Above Ground Pools |
 |
|
|
|
With the Hayward Pro Series sand filter for above ground pools, you can enjoy the many benefits of having a Pro working on your side. Dependable and easy to use, these Hayward above ground pool filters will make your pool maintenance routine more convenient. Best of all, Hayward Pro Series filters will help you to ensure that your pool remains an inviting, crystal clear oasis all season long.
Technical Specifications:
FILTER:
• Durable, corrosion-proof filter tank molded of color-fast material for long-lasting, all-weather performance.
• 7-position PermaGlass XL™ Vari-Flo valve provides maximum flow at lower pressure drop.
• Flange clamp design allows 360 degree rotation for easy installation.
• Integral top diffuser ensures even distribution of water over the entire sand bed for maximum use of the filtration area.
• Precision engineered umbrella-fold self cleaning laterals for balanced flow and backwashing, plus easy serviceability.
• Large pressure sand/water drain for rapid winterizing .
PUMP:
• The above-ground industry's largest strainer basket for large debris collection with minimal maintenance.
• Horizontal/vertical discharge feature -- simply converts from vertical to horizontal discharge orientation with the press of a button.
• Quick disconnect intake and discharge pipe connection.
• C-Clip Connector allows for easy disengagement of strainer housing in a matter of seconds for hassle-free maintenance.
• Heavy-duty, high performance motor with integrated automatic thermal overload protector for years of operation.
• High quality Noryl® impeller with wide openings to prevent clogging by leaves and debris.
• Durable, corrosion-proof housing for years of dependable service and all-weather performance.
• Heat-resistant, double-sized seal for long-lasting efficiency
.
• Energy-efficient, protected rear mounted switch.
• Integral drain plug for easy winterization of pump.
Back To The Top
Troubleshooting:
FILTER:
LOW WATER FLOW:
– Check skimmer and pump strainer baskets for debris.
– Check for restrictions in intake and discharge lines.
– Check for air leak in intake line (indicated by bubbles returning to pool).
– Backwash filter.
SHORT FILTER CYCLES:
– Check for algae in pool and super chlorinate as required.
– Be sure chlorine and pH levels are in proper range (adjust as required).
– Check surface of filter sand for crusting or caking (remove 1” of sand if necessary).
POOL WATER WON’T CLEAR UP:
– Check chlorine, pH and total alkalinity levels and adjust as required.
– Be sure flow rate through filter is sufficient.
– Operate filter for longer periods.
– Be sure multiport valve is set on “Filter” position.
SAND AND DEBRIS ENTERING THE POOL:
– Check laterals, standpipe and lateral hub for damage (replace as required).
– Be sure there isn't too much sand in the filter itself.
PUMP:
Motor Will NOT Start – Check For:
– Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown fuses.
– Manually check rotation of motor shaft for free movement and lack of obstruction.
– If you have a timer, be certain it is working properly. Bypass it if necessary.
Motor Shuts OFF – Check For:
– Undersized wiring; loose connections; etc.
– Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use).
– Mechanical binding and electrical overloads.
NOTE: Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector” will allow the motor to automatically restart once the motor has cooled, provided the power source is again up to proper levels. It will continue to cut On/Off until the problem is corrected. Be sure to correct cause of overheating.
Motor Hums, But Does NOT Start – Check For:
– Centrifugal switch stuck in OPEN position.
– Binding of motor shaft.
Pump Won’t Prime:
– Make sure pump/strainer housing is filled with water and the cover O-ring is clean, also be sure it is properly seated in the cover O-ring groove. Make sure strainer cover is locked firmly in position and lubricated with “Jack’s 327.”
– Make sure all suction and discharge valves are fully open and not blocked, that pool water level is at proper level, and that skimmer weir is not hung up or binded on skimmer wall.
– Block off to determine if pump will develop a vacuum. You should have 5”-6” of vacuum at the strainer cover (Only your pool dealer can confirm this with a vacuum gauge). You may be able to check by removing the skimmer basket and holding your hand over the bottom port with skimmer full and pump running. If no suction is felt, check for line blockage
– If pump develops a vacuum, check for blocked suction line or dirty strainer basket, an air leak in the suction piping may be the cause.
– If pump does not develop a vacuum and pump has sufficient “priming water”:
1. Re-check strainer housing cover and all threaded connections for suction leaks. Check if all hose clamps are tight.
2. Check voltage to ensure that the motor is rotating at full RPM’s.
3. Open housing cover and check for clogging or obstruction in suction. Check impeller for debris.
4. Remove and replace shaft seal only if it is leaking.
Back To The Top
Frequently Asked Questions:
What does the system come with?
– This system includes the 18” sand filter, a 1 HP pump, a system base, and pump to filter plumbing kit.
How much sand will I need for this filter?
– You will need 150 pounds of sand for the 18 inch sand filter.
What is the maximum pool gallonage for this filter?
– This system can filter a pool up to 16,800 gallons.
What kind of sand will I need and where would I purchase it?
– #20 silica sand, which can be purchased at a local pool store or hardware store. Costing about $4.00 per bag.
How many microns will the Hayward filter, filter down to?
– Sand filters can filter down to 20-23 microns.
How often do I have to change the sand?
– You should change the sand in your sand filter every 2-3 years.
How much area is needed for the Hayward 18” System?
– Width = 29”
– Length = 15-1/2”
– Height = 35”
How long is the cord on the pump ane vd what is tholtage?
– Powered by our high-flow rate, 115V pump with a 6 ft. cord and plug suitable for a GFCI outlet.
What are the different positions on the 6 Position Multiport Valve?
– Filter, waste, closed, backwash, recirculate, and rinse.
Back To The Top
|
For written information, order our Information Packet located below.
|
http://www.spa-usa.com/Pool-Equipment/Filters-and-Pumps-for-Above-Ground-Pools/Hayward-Pro-Series-Sand-Filter-Systems-for-Above-Ground-Pools/
|
|